Leave Your Message

How to Plan Dual Color Work with a Truck Mounted Road Marking Machine

2026-10-29

Does a highway crew make extra passes because white and yellow lines cannot be applied in the planned sequence? The delay may come from the equipment plan, not the paint. A truck mounted road marking machine needs the correct pumps, guns, controls, and material paths for dual-color work.

Buyers should map the line schedule before choosing a configuration. A truck mounted road marking machine may support two colors, two line patterns, or several guns, but each setup needs clear operating rules. Good planning reduces color change time, contamination risk, and avoidable lane closures.

Map the Route by Color and Pattern

List every line by color, width, pattern, length, and working side. Separate edge lines from center lines, ramps, crossings, and channels. Mark paired colors and continuous-plus-broken patterns. This map shows whether a truck mounted road marking machine should apply both lines in one pass or complete separate runs.

 screenshot-20261029-143038.png

 screenshot-20261029-143052.png

 

Decide Between Simultaneous and Sequential Work

Simultaneous marking can reduce travel and traffic-control time. It also demands compatible paint, stable flow, correct gun spacing, and enough room for both material circuits. Sequential work may be better when colors use different formulas or the route changes often. Ask the supplier to show how the truck mounted road marking machine switches patterns, isolates each color, and prevents one circuit from affecting the other.

Protect Each Material Circuit

Confirm the tank, pump, hose, filter, return path, and gun assigned to each color. Review paint data sheets for viscosity, solvent, temperature range, and cleaning method. Do not assume two colors of the same product name behave the same. A truck mounted road marking machine needs labeled connections and a written flushing plan. The crew should know which parts can be shared and which must stay separate.

Match Flow to Guns and Line Width

Heavsty lists a dual-cylinder, dual-pump Graco airless system on the CB-T1. Its continuous flow is 18 L/min, and the listed spray width ranges from 50 to 900 mm across multiple guns. These figures define the available system range. The final truck mounted road marking machine setup must still be tested with the chosen paint, speed, film thickness, gun count, and line schedule. Avoid planning every gun at its maximum demand.

 screenshot-20261029-143107.png

 screenshot-20261029-143119.png

 

Coordinate Pattern and Vehicle Control

A truck mounted road marking machine must control line start, stop, spacing, pressure, and vehicle speed without losing the route. Heavsty lists touchscreen control and stepless hydraulic drive on the CB-T1. The related dual-pump platform can support single-line, double-line, and continuous-plus-intermittent work when configured for the task. A truck mounted road marking machine should store or document the approved settings for each pattern so shifts can repeat them.

Plan Beads and Finished Line Checks

Color and pattern are only part of the acceptance result. Define bead type, feed rate, spread width, timing, and inspection method for each line. The CB-T1 lists a 200 kg glass bead tank for extended work. Confirm how the bead system follows both gun paths and pattern changes. During the trial, inspect the truck mounted road marking machine for clean edges, correct spacing, stable thickness, even bead coverage, and no color carryover.

Run a Full Dual Color Trial

A short single-color line cannot prove a truck mounted road marking machine setup. Test the truck mounted road marking machine with both approved colors and the hardest planned pattern. Include starts, stops, turns, speed changes, and a normal refill or cleaning step. Record pressure, flow, gun layout, vehicle speed, pattern settings, and material batch. Approve the dry line before shipment or full production.

Request a Project Based Configuration

Heavsty supplies dual-pump airless platforms, cab controls, multi-gun layouts, adjustable spray widths, and bead systems for large road projects. These options allow a truck mounted road marking machine to be matched to the color and pattern plan rather than a general catalog setup.

Send Heavsty your route drawings, color schedule, paint data, line widths, patterns, film thickness, bead needs, climate, chassis limits, and daily target. The team can review the complete truck mounted road marking machine configuration and trial plan. Ask for a proposal that covers equipment, training, spare parts, and acceptance records.